Konica magicolor 5430 manual

Select the default settings for your printer, such as the default media format you use. This section describes how to uninstall the magicolor DL Printer Driver if necessary.

Then click Uninstall. Windows NT 4. To save the current settings, enter a name, and then click Save. Afterward, the saved settings can be selected from the drop-down list. Select Default from the drop-down list to reset the functions in all tabs to display to their default values. Check this option button to display a sample of the page layout in the figure area. Check this option button to display an image of the printer with all installed options in the figure area.

From the Display menu, choose Status Reduce to decrease the size of the window. From the Display menu, choose Status Expand to increase the size of the window. When the background of the right-hand printer graphic is green, the printer is in standby mode or a job is printing normally. When the background of the right-hand printer graphic is red, there is an error and the job has been interrupted. The status of the printer and the error message are shown in the dialog boxes on the left.

Printer Status —Displays text messages that describe the current operational status of the printer. How to Recover —Provides you with explanations of what you need to do in order to correct problems and recover from error conditions. Warning Status —Displays text messages that alert you of conditions such as low toner. Printer Status Figure —Shows a graphic representation of the printer and indicates where the problem is.

Printing Status —Displays the status of the current print job. Select Popup Message —Allows you to choose which message s you want to bring to the foreground when that particular condition occurs with the printer. Printer Information —Allows you to check various information such as the number of prints.

Supplies Status —Displays the usage status approximate percentage remaining of each toner cartridge. When the Status Display detects a printing problem, the icon on the Windows task bar changes from green to yellow or red, depending on the severity of the printer problem. When the Status Display notifies you of a printing problem, double-click its icon on the Windows task bar to open the Status Display. The Status Display identifies what type of error has occurred. To close the Status Display from the File menu, choose Exit.

Double-click the icon to open the Status Display window again. Printer Status Monitor Center is an application that shows the status of multiple printing devices connected to the host through local ports USB or network ports. Follow the appropriate operation described below to open the Printer Status Monitor Center. Printer Name —Displays the model name of the local printer or printer on the network together with a printer icon. The printer icon changes color according to the connection and printer status.

A red icon indicates an error, a yellow icon indicates a warning, and a green icon indicates normal operation. Depending on the setting in the Options dialog box, Status Display or PageScope Web Connection appears when you double-click the printer name. Port —Displays the name of the port where the printer is connected.

For a local printer, the type USB is displayed. Status —Displays the printer status. The same information for Printer Status in the Status Display is displayed. The listed values are, from the left: C cyan , M magenta , Y yellow and K black. Update Printers —Searches again for the printers on the network.

Network Printers —Allows the IP address of network printers to be added or removed. If a red or yellow icon appears, open Status Display or PageScope Web Connection, and then check the detailed information. In addition, it displays the current status of the printer, including any condition that needs your attention.

Press the Right or Left keys to select either. The indicators shown below will appear, indicating the amount of toner that remains in the yellow Y , magenta M , cyan C , and black K toner cartridges. The menus with settings that can be set from the control panel of the magicolor DL are structured as shown next page. If the printer is connected to a network, the following settings should be specified.

For details about each setting, contact your network administrator. ON enables the Internal Web. Select from a 10Base-T connection 10M ,. If AUTO is selected, the transmission speed is set. Select whether data is. If AUTO is selected, the transmission. The third value indicates the negotiation NEG. When set to ON , negotiation is performed.

When set. Before purchasing a large quantity of special media, do a trial printing with the same media and check the print quality. Keep media on a flat, level surface in its original wrapper until it is time to load it. For a list of approved media, refer to printer. Suitable for plain paper laser printers, such as standard or recycled office paper. Do not use the media types listed below. These could cause poor print quality, media misfeeds, or damage to the printer.

Coated with a processed surface such as carbon paper, digitally glosscoated media, and colored paper that has been treated. Unapproved iron-on transfer media such as heat-sensitive paper, heat-pressure paper, and heat-press transfer paper.

Designed specifically for inkjet printers such as superfine paper, glossy paper, glossy film, and postcards. Toner does not adhere well to moist or wet paper. Test all thick stock to ensure acceptable performance and to ensure that the image does not shift. Mixed with any other media in the trays as this will cause printer misfeeding.

Print on the front address side only. Some parts of the envelope consist of three layers of paper—the front, back, and flap. Anything printed in these layered regions may be lost or faded. Common office envelopes approved for laser printing with diagonal joints, sharp folds and edges, and ordinary gummed flaps. Using envelopes with emulsion-based glue avoids this problem. Tape seals, metal clasps, paper clips, fasteners, or peel-off strips for sealing. A sheet of labels consists of a face sheet the printing surface , adhesive, and a carrier sheet:.

The face sheet surface must cover the entire carrier sheet, and no adhesive should come through on the surface. You can print continuously with label sheets. However, this could affect the media feed, depending on the media quality and printing environment. If problems occur, stop the continuous printing and print one sheet at a time.

Format label data within your application. Try printing your data on a sheet of plain paper first to check placement. Check your application documentation for more information on printing labels. Format letterhead data within your application. Format postcard data within your application. Do not fan transparencies before loading them. Resulting static electricity may cause printing errors.

If you touch the face of the transparencies with your bare hands, print quality may be affected. Keep the printer path clean. Transparencies are especially sensitive to a dirty media path. You can print continuously with transparencies.

However, this could affect the media feed, depending on the media quality, static buildup, and printing environment. Format the information to be printed on the transparencies within your application.

Welcome to ManualMachine. We have sent a verification link to to complete your registration. Log In Sign Up. Forgot password? Enter your email address and check your inbox. Please check your email for further instructions. Enter a new password. Konica Minolta. Contents 1 Introduction Contents i. Contents iii. Getting Acquainted with Your Printer Space Requirements To ensure easy operation, supply replacement and maintenance, adhere to the recommended space requirements detailed below.

Printer Parts The following drawings illustrate the parts of your printer referred to throughout this guide, so please take some time to become familiar with them. Front View 1 2 3 1—Control panel 4 2—Output tray 3—Top cover 12 4—Fuser unit 11 5—Right side cover 5 6—Transfer roller 7—Transfer belt unit 10 6 8—Tray 1 Multipurpose cassette 9 8 7 9—Grip 10—Front cover 6 11—Waste toner bottle 12—Toner cartridge 7 11 Getting Acquainted with Your Printer 3.

PageScope Web Connection With the web browser, the status of printers can be checked, and each setting can be changed. For details, refer to the magicolor DL Reference Guide. System Requirements 7. The option moves to the Installed Options list. Uninstalling the Printer Driver for Windows 9. OK Click to exit the Properties dialog box, saving any changes made. Cancel Click to exit the Properties dialog box without saving any changes made.

Apply Click to save all changes without exiting the Properties dialog box. Help Click to view the help. Easy Set To save the current settings, enter a name, and then click Save. Page Layout Check this option button to display a sample of the page layout in the figure area.

Printer Figure Check this option button to display an image of the printer with all installed options in the figure area. Using the Printer Driver Working with the Status Display Introduction The Status Display shows information about the current status of the printer. Using the Status Display When the background of the right-hand printer graphic is green, the printer is in standby mode or a job is printing normally.

The function areas include: Printer Status —Displays text messages that describe the current operational status of the printer. Recognizing Status Display Alerts When the Status Display detects a printing problem, the icon on the Windows task bar changes from green to yellow or red, depending on the severity of the printer problem.

Recovering from a Status Display Alert When the Status Display notifies you of a printing problem, double-click its icon on the Windows task bar to open the Status Display. Recognizing Status Display Alerts Using the Printer Status Monitor Center Printer Name —Displays the model name of the local printer or printer on the network together with a printer icon.

For a network printer, the IP address is displayed. Action Menu Update Printers —Searches again for the printers on the network. The menus with settings that can be set from the control panel of the magicolor DL are structured as shown below.

The display language of the message window can be changed to the required language. If the printer is connected to a network, the following settings should be specified.

For details about each setting, contact your network administrator. ON enables the Internal Web. SPEED indicates the network transmission speed. If AUTO is selected, the transmission speed is set depending on the negotiation.

Therefore, there is no setting where negotiation NEG. DUP indicates the communication method for bi-directional communication. When set to ON , negotiation is performed. When set to OFF , negotiation is not performed. Before purchasing a large quantity of special media, do a trial printing with the same media and check the print quality. Keep media on a flat, level surface in its original wrapper until it is time to load it. For a list of approved media, refer to printer.

Suitable for plain paper laser printers, such as standard or recycled office paper. Do not use the media types listed below. These could cause poor print quality, media misfeeds, or damage to the printer. Coated with a processed surface such as carbon paper, digitally glosscoated media, and colored paper that has been treated. Unapproved iron-on transfer media such as heat-sensitive paper, heat-pressure paper, and heat-press transfer paper.

Designed specifically for inkjet printers such as superfine paper, glossy paper, glossy film, and postcards. Toner does not adhere well to moist or wet paper. Test all thick stock to ensure acceptable performance and to ensure that the image does not shift. Mixed with any other media in the trays as this will cause printer misfeeding.

Print on the front address side only. Some parts of the envelope consist of three layers of paper—the front, back, and flap. Anything printed in these layered regions may be lost or faded. Common office envelopes approved for laser printing with diagonal joints, sharp folds and edges, and ordinary gummed flaps.

Using envelopes with emulsion-based glue avoids this problem. Tape seals, metal clasps, paper clips, fasteners, or peel-off strips for sealing. A sheet of labels consists of a face sheet the printing surface , adhesive, and a carrier sheet:. The face sheet surface must cover the entire carrier sheet, and no adhesive should come through on the surface. You can print continuously with label sheets. However, this could affect the media feed, depending on the media quality and printing environment.

If problems occur, stop the continuous printing and print one sheet at a time. Format label data within your application. Try printing your data on a sheet of plain paper first to check placement. Check your application documentation for more information on printing labels. Format letterhead data within your application. Duplexing See page 32 for supported sizes face up—top of page first.

Format postcard data within your application. Do not fan transparencies before loading them. Resulting static electricity may cause printing errors. If you touch the face of the transparencies with your bare hands, print quality may be affected. Keep the printer path clean. Transparencies are especially sensitive to a dirty media path. You can print continuously with transparencies. However, this could affect the media feed, depending on the media quality, static buildup, and printing environment.

Format the information to be printed on the transparencies within your application. Welcome to ManualMachine. We have sent a verification link to to complete your registration. Log In Sign Up. Forgot password? Enter your email address and check your inbox. Please check your email for further instructions. Enter a new password. Konica Minolta. Magicolor DL. Contents i.

Contents iii. Getting Acquainted with Your Printer Space Requirements To ensure easy operation, supply replacement and maintenance, adhere to the recommended space requirements detailed below. Printer Parts The following drawings illustrate the parts of your printer referred to throughout this guide, so please take some time to become familiar with them.

Front View 1 2 3 1—Control panel 4 2—Output tray 3—Top cover 12 4—Fuser unit 11 5—Right side cover 5 6—Transfer roller 7—Transfer belt unit 10 6 8—Tray 1 Multipurpose cassette 9 8 7 9—Grip 10—Front cover 6 11—Waste toner bottle 12—Toner cartridge 7 11 Getting Acquainted with Your Printer 3.

PageScope Web Connection With the Web browser, the status of printers can be checked, and each setting can be changed. For details, refer to the magicolor DL Reference Guide.

System Requirements 7. The option moves to the Installed Options list. Click Apply. Click OK to exit from the Properties dialog box. Uninstalling the Printer Driver For Windows 9. OK Click to exit the Properties dialog box, saving any changes made.

Cancel Click to exit the Properties dialog box without saving any changes made. Apply Click to save all changes without exiting the Properties dialog box. Help Click to view the help. Easy Set To save the current settings, enter a name, and then click Save. Page Layout Check this option button to display a sample of the page layout in the figure area. Printer Figure Check this option button to display an image of the printer with all installed options in the figure area.

Using the Printer Driver Working with the Status Display Introduction The Status Display shows information about the current status of the printer. Using the Status Display When the background of the right-hand printer graphic is green, the printer is in standby mode or a job is printing normally. The function areas include: Printer Status —Displays text messages that describe the current operational status of the printer. Recognizing Status Display Alerts When the Status Display detects a printing problem, the icon on the Windows task bar changes from green to yellow or red, depending on the severity of the printer problem.

Recovering from a Status Display Alert When the Status Display notifies you of a printing problem, double-click its icon on the Windows task bar to open the Status Display. Recognizing Status Display Alerts Using the Printer Status Monitor Center Printer Name —Displays the model name of the local printer or printer on the network together with a printer icon.

For a network printer, the IP address is displayed. Action Menu Update Printers —Searches again for the printers on the network.

The default setting is Status Display. This setting only applies to network printers. Timeout Two timeout intervals can be specified. Indicator Off On 1 The printer is not ready The printer is ready to to accept data. The printer requires operator attention usually accompanied by a status message in the message window.

Key Function 3 Cancels the currently displayed menu or menu choice Allows you to cancel one or all print jobs that are currently being printed or processed: 1. Press the Cancel key. Press the Select key. The print job s is cancelled. Within a menu choice that is changeable character by character, scrolls downward through the available characters 8 Moves left in the menu structure Moves left through the available menu choices.

About the Control Panel Toner Supply Indicators The indicators shown below will appear, indicating the amount of toner that remains in the yellow Y , magenta M , cyan C , and black K toner cartridges. Configuration Menu Overview MAP Language Menu. The default setting is English. When set to STOP , printing stops when the toner cartridge is empty. The Energy Saver mode is automatically can- celled when any of the following occurs: The printer is restarted. A print job is received. Any key on the control panel is pressed.

The front cover or right side cover is opened, then closed. A tray is opend, then closed. When set to OFF , the printer stops and displays a message indicating that media should be loaded into the specified tray if the specified tray runs out of media.

Use this submenu to view information related to the engine. In addition, the administrator password is reset to the default password. Network Menu If the printer is connected to a network, the following settings should be specified. IP Setting Use the Up, Down, Left, and Right keys to enter the value.

MAC Displays Ethernet hardware address for this printer. Media Specifications What types and sizes of media can I load? Custom, Minimum 3. Media Types Before purchasing a large quantity of special media, do a trial printing with the same media and check the print quality. Use media that is Suitable for plain paper laser printers, such as standard or recycled office paper. Note Do not use the media types listed below.

DO NOT use media that is Coated with a processed surface such as carbon paper, digitally glosscoated media, and colored paper that has been treated Carbon backed Unapproved iron-on transfer media such as heat-sensitive paper, heat-pressure paper, and heat-press transfer paper Cold-water-transfer paper Pressure sensitive Designed specifically for inkjet printers such as superfine paper, glossy paper, glossy film, and postcards Already been printed on by another printer, copier, or fax machine Dusty Wet or damp.

Media Types Capacity Tray 1 Up to 20 thick stock sheets, depending on their thickness. Envelopes Print on the front address side only.

Approved for laser printing Dry DO NOT use envelopes that have Sticky flaps Tape seals, metal clasps, paper clips, fasteners, or peel-off strips for sealing Transparent windows Too rough of a surface Material that will melt, vaporize, offset, discolor, or emit dangerous fumes Been presealed. Labels A sheet of labels consists of a face sheet the printing surface , adhesive, and a carrier sheet: The face sheet must follow the plain paper specification.

Are precut or perforated Do not use OK to use Shiny backed paper Full-page labels uncut Letterhead Format letterhead data within your application. Postcards Format postcard data within your application. Use postcards that are Recommended for laser printers DO NOT use postcards that are Coated Designed for inkjet printers Precut or perforated Preprinted or multicolored may result in media misfeeds " If the postcard is warped, press on the warped area before putting it in Tray 1.